陕西快乐十分单式玩法
吹塑托盤|吹塑托盤廠家-山東東星塑料托盤有限公司
返回首頁 | 收藏本站

新聞中心 News Center

聯系我們

公司名稱:山東東星塑料托盤有限公司

聯系人:王經理

手機:18653435397 13884696099

電話:0534-3223000

傳真:0534-3223001

郵箱:[email protected]

網址:www.qreql.icu

地址:山東省慶云縣開發區新華路東首

當前位置:主頁 > 技術交流 >

技術交流 /

1000升IBC噸桶使用說明

標簽:     閱讀次數:    文章分類:技術交流    Posttime:2013-08-30 10:24
1000升IBC噸桶使用說明
IBC噸桶使用說明
OPERATION INSTRUCTION OF IBC
1、灌裝及儲存 使用者在灌裝前須進行灌裝物與本容器原材料的化學相容性試驗。灌裝時先打開灌裝口蓋,插
入外徑小于140mm的管子實施灌裝,灌裝完畢后擰緊密封蓋。熱灌裝要求小于70°C, 并等到灌裝物冷卻至環境溫
度后再擰緊封蓋。注意遮蓬貯存,避免曝曬。
FILLING &STORAGE Users should make an experiment to ensure the chemical compatibility of the liquid
to be filled with the raw material of the IBC. In the course of filling please remove the top filling
lip, then fill though the pipe with external diameter less than 140mm,finally tighten all closures
after filling. The temperature of hot filling shall not exceed 70°C. Closures shall be screwed tightly
until the liquid is cooled to normal atmospheric temperature.
2、排液打開頂部的灌裝口蓋,旋下閥門前端螺紋蓋,撕開封閉用的鋁膜;如使用閥門接管,請將其連同墊圈套在
螺紋蓋中,擰回放料閥并擰緊。也可采用其它合適的接口放料。然后卸門手柄上的鎖閉螺絲,再將閥門手柄順時
針扳動以開始放料。放料完畢后逆時針轉手柄關閉閥門,裝上鎖閉螺絲,旋上放料閥密封蓋和灌裝口蓋。
DISCHARGE Remove the top filling lid. Unscrew and remove sealing cap from the discharge valve. Cut
off Alnm foil. When using valve nozzle for easy drain, please insert nozzle into the sealing cap and
screw the cap onto the discharge valve with gasket and tighten it. Or use other adaptors for discharge.
Unscrew the locking bolt of the valve handle. Rotate the valve handle clockwise to begin discharge.
After discharge please rotate the valve handle counterclockwise to seal the valve, install the security
bolt and screw the sealing cap of discharge valve and top filling lid.
3、裝卸本容器的提升方式為底部提升,不允許使用頂部提升方式。底部提升時,叉車的叉臂進入叉孔并超過對
面底部鋼框后方可提升。堆碼時務必把上面容器底部鋼框放置在下面容器頂部鋼框內,不允許叉臂碰撞內容器、
鋼框架、閥門、護角以及托盤中除叉孔以外的部位。
LIFTING Only lifting IBCs from the bottom is permitted. Lifting form the top is forbidden.
4、車輛或集裝箱內裝載 IBC桶包裝貨物運輸時,集裝箱或車輛應具備至少同容器等高的剛性圍壁和圍欄。裝載
兩層時,務必在車箱或集裝箱內放置合適的緩沖物并加以捆扎。
LOADING IN TRUCK OR ISO CONTAINER The ISO containers or vehicles should be equipped with rigid wall
or surrounding bar which are not lower than the high of the IBCs. When two high of loading is permitted,
users shouid place proper cushions and take methods to fix every IBC.
5、日常維護和檢查 嚴禁閥門和內容器受到外力沖擊和碰撞。在二次回用灌裝前,必須對返回容器的狀態進行仔
細檢查,例如內容器和框架是否被撞擊過從形成泄漏點或影響正常裝卸和堆碼。特別需要對閥門進行檢查,注意
安裝在閥門根部鋁緊固螺帽和內容器結合部是否緊密。
MAINTENANCE &INSPECTION The valve inner container of IBC must be protected strictly from hitting
or colliding . Before refilling users should check the condition of recycled container to avoid any
unsafety. Specially a check must be done for the valve.

上一篇:塑料托盤的選擇
下一篇:吹塑托盤比注塑托盤的優越性在哪里

Copyright © 2012-2018 JINKE. 東星塑料托盤 版權所有   技術支持:德州筑巢
主營產品:吹塑托盤
陕西快乐十分单式玩法